NitroMax
An unlimited supply of heated nitrogen for your spray booths: an in-house "nitrogen on demand" generator that removes the need for high-pressure tanks.

Less waste. Faster cycles. A better finish.
Transfer efficiency
Spraying with a single gas (N2) minimizes overspray, so less material is wasted and a higher volume of paint reaches the part.
Flash time
Nitrogen from the NitroMax is inert and dry. Heat added through the heated hose to the spray gun speeds up flash time and productivity.
Finish quality
The absence of moisture ensures a higher quality finish, with far less buffing and sanding.
Cycle time
Faster flash times, better transfer efficiency and a cleaner finish result in improved cycle times.
Why spray with nitrogen?
The problem with compressed air
Spray guns have relied on compressed air since the early 1900s, and moisture in that air has always been a challenge. Inline filtration, refrigerated drying and point-of-use filters remove some of it, but with minimal benefit to the paint. When you spray with compressed air, you atomize the paint with the mix of gases in our atmosphere, moisture included.
A single, dry gas
The ideal propellant has no moisture, hence nitrogen: the most abundant gas in our atmosphere. Separating the oxygen and moisture out of compressed air gives the cleanest, driest medium for spray applications. Atomizing with a single gas is far more efficient than with a mix of gases.
Adding heat
Nitrogen's inert qualities allow heat to be added without side effects. Heated nitrogen speeds curing and drying, and atomization happens at lower pressures. That means less overspray and wasted material, significantly fewer VOCs exhausted into the atmosphere, and longer-lasting spray booth exhaust filters.
Nitrogen on demand
Spray painting needs large volumes of nitrogen. An in-house NitroMax generator supplies it continuously, with no high-pressure tanks and none of the handling rules that come with them.
Further reading: What you need to know about spraying finishes with nitrogen, by technical journalist Tim Sramcik.

Which NitroMax is right for my shop?
Size the system by the number of spray booths and painters. You need one HeatPro 200 with a 50 ft heated hose for each booth or prep station.
| System | Spray booths | Painters | HP200 + 50 ft hose | Min air volume | Min air pressure | Receiver tank |
|---|---|---|---|---|---|---|
| NM15 | 1 | 1 | 1 | 20 cfm / 566 lpm | 100 psi / 7 bar | Optional |
| NM15 | 2 | 1 | 2* | 20 cfm / 566 lpm | 100 psi / 7 bar | Optional |
| NM30 | 2 | 2 | 2 | 40 cfm / 1132 lpm | 100 psi / 7 bar | Optional |
| NM30 | 3 | 2+ | 3* | 40 cfm / 1132 lpm | 100 psi / 7 bar | 100 gal / 350 L |
| NM30 | 4 | 2+ | 4* | 40 cfm / 1132 lpm | 100 psi / 7 bar | 130 gal / 500 L |
* Additional HP200 heaters are required. See installation notes for the recommended layout.
NitroMax systems & parts
- NM15Single booth N2 generator with 1 × HP200 and 1 × NHH50 heated hose$26,705
- NM30Dual booth N2 generator with 2 × HP200 and 2 × NHH50 heated hoses$39,458
- NG15Single booth nitrogen generator only$21,108
- NG30Dual booth nitrogen generator only$28,339
- NGS-4Service kit (1 × coalescent, 3 × active carbon cartridges)$546.50
All prices exclude shipping, installation and training. Full price list & finance →
NitroMax 30 at a glance
- Product code
- NM30 (Nitromax 30)
- Description
- Nitrogen generator
- Max flow rate
- 30 cfm (850 LPM)
- Max inlet pressure
- 145 psi (10 bar)
- Pressure drop
- 10 psi (0.6 bar)
- Electrical
- 110 / 220 VAC, 50–60 Hz
- Current draw
- 2 A
- Filtration
- 5 stage
- Enclosure
- Aluminium
- Dimensions (H × W × D)
- 44 × 24 × 18 in (1117 × 609 × 457 mm)
- Connections
- ½" FNPT inlet and outlet
- Shipping weight
- 180 lb (95 kg)
- Made in
- USA
- Certifications
- UL, CSA, ETL, CE
Brochures, layouts & ROI
Ready to spray with heated nitrogen?
Tell us about your booths and painters, and we'll size a NitroMax system for your shop.
